| attah | piggz: So, now, what do i do? | 16:08 |
|---|---|---|
| piggz[m] | What stage are you? | 16:09 |
| attah | unboxed xD | 16:10 |
| piggz[m] | well, you start at https://github.com/sailfish-on-dontbeevil/documentation/wiki | 16:12 |
| piggz[m] | and validate my documentation :) | 16:12 |
| piggz[m] | one thing to note .. first step is to install tow-boot to the spi flash...which is what i have, though, i heard recently about a better bootloader that may be worth trying | 16:13 |
| attah | Ah, i was staring at a two-line readme (: | 16:13 |
| piggz[m] | there is this u-boot based bootlaoder to try https://xnux.eu/log/092.html | 16:13 |
| attah | i'll try the basic way first | 16:14 |
| attah | oh ffs, tow-boot doesn't give where to run the commands, and don't give paths.... oh, joy | 16:15 |
| attah | it looks like on device... buy why specify ^^ | 16:16 |
| piggz[m] | you write the spi-flash installer to an sd card, then install the sdcard in the ppp and boot from it to install | 16:22 |
| attah | okay, it was pebkac | 16:23 |
| attah | they just put it in backwards importance | 16:23 |
| attah | note to self: eat first | 16:24 |
| attah | Not following my own advice is a bad idea | 16:40 |
| attah | piggz[m]: so jumpdrive isn't a thing, and therefore emmc isn't a thing? | 16:42 |
| piggz | attah: i dont think jumpdrive is needed on ppp with towboot .. im sure towboot enabled emmc to be exported | 16:43 |
| attah | so... how do i get the image onto emmc then? | 16:43 |
| attah | (because flash-it seems to wand an sd card) | 16:45 |
| piggz[m] | use towboot to export emmc as usb-storage, then use flash-it to install to that | 16:46 |
| attah | So i guess my first suggestion is to remove jumprive from the guide, and mention that vol-up puts tow-boot in emmc mass storage mode | 16:53 |
| attah | The script did go through, with some stuff that looked bad, though it claimed success | 16:53 |
| attah | Now food, and then i'll try again | 16:54 |
| piggz[m] | i can invite you to the project and you can update the wiki ;) | 16:58 |
| attah | i'll PR something when done | 17:07 |
| attah | piggz[m]: wohoo! Second flash lucky | 17:29 |
| piggz[m] | cool ... you will want to get through the setup, ssh in over wlan, and zypper ref/dup to get todays kernel with usb crash fix | 17:30 |
| attah | Guess i need to let it charge some more... it is *really* upset despite a cable | 17:39 |
| attah | And bootloops... so i guess it will never actually get any charge in | 17:39 |
| attah | into the mass storage mode it goes, and hope for the best | 17:40 |
| attah | piggz[m]: I'm getting 400mA current draw while booted, and almost another amp while charging when it finally decided to stop looping | 18:31 |
| attah | And wifi is failing as if wrong password, though it is both pretty trivial and triple-checked | 18:38 |
| attah | Trying to change my router settings out of WPA2/3 mixed - and it just dies for 90 seconds and reverts | 18:46 |
| attah | Oh joy | 18:46 |
| attah | piggz: any ideas why the wifi config might not like my router? or better yet, workarounds? | 19:11 |
| piggz[m] | not sure .. it connects to mine! | 19:11 |
| attah | My 2.4GHz had pure WPA2 configured, and it still doesn't like it | 19:11 |
| attah | piggz[m]: connected fine to my 10 III hotspot... ref'd and dup'd | 19:37 |
| attah | aaand it's dead | 19:37 |
| attah | It is just not my day today | 19:38 |
| attah | piggz[m]: Re-flashed, re-updated, reproduced :( | 19:58 |
| ender | WPA2/3 mixed works for me, but pure WPA3 doesn't | 21:56 |
Generated by irclog2html.py 2.17.1 by Marius Gedminas - find it at https://mg.pov.lt/irclog2html/!